If you shop at Amazon.com (for anything), use this link to support FordTaurus.net!

Rear seat sits high?

Post Reply
Tech88
Regular Member
Posts: 24
Joined: Fri Nov 09, 2018 5:22 pm
Vehicle: 13' PI

Rear seat sits high?

Post by Tech88 » Wed May 29, 2019 6:14 pm

I noticed the rear seat cushion sits noticeably high. Is there a way to make it lower?


Jake_Blues
Regular Member
Posts: 69
Joined: Sun Jan 27, 2019 8:25 pm
Vehicle: 2013 Police Interceptor Sedan

Re: Rear seat sits high?

Post by Jake_Blues » Thu May 30, 2019 10:07 pm

is it the factory cloth/vinyl seat or an aftermarket one?

if it's oem it could be that the seat was removed and just isn't wasn't "re-seated" properly.

if you lift up the back seat, you'll find that to accommodate the rear end collision bracing the foam on the bottom of the seat has been cut to allow the seat to fit over the steel cross members.

it could also be that the seat you have doesn't have the foam trimmed to fit.

Tech88
Regular Member
Posts: 24
Joined: Fri Nov 09, 2018 5:22 pm
Vehicle: 13' PI

Re: Rear seat sits high?

Post by Tech88 » Thu May 30, 2019 10:54 pm

I'll have to check tomorrow. I know my PI has an administrative package with factory center console and carpet. So I assume it's a factory seat correct to the car

billross
Regular Member
Posts: 26
Joined: Sun May 21, 2017 1:46 am
Location: Minneapolis, MN
Vehicle: 2013 Taurus Police Interceptor

Re: Rear seat sits high?

Post by billross » Fri May 31, 2019 1:13 am

My car was like that too when I got it from the auction. The foam cushion under the rear seat has "channels" carved into it to fit over the crash bars under the seat. Apparently before they sent my car to auction, they removed the back seat-bottom and then reinstalled it without taking the time to fit the channels in the foam around the crash bars. So the seat-bottom foam was sitting on top of the crash bars rather than sitting around the crash bars. Pull up the seat-bottom to check it out. You'll see what we're talking about...
-Bill
Daily Driver: 2013 Taurus Police Interceptor, Smokestone, All-wheel drive, 44,000 miles, 1,500 idle hours.
2nd Daily Driver: 2007 Crown Vic P71, Smokestone Metallic, SAP, 101,000 miles, 330 idle hours.
Weekend Driver: 2014 Shelby GT500 Coupe, Ruby Red Metallic, Stripe Delete, SVT Performance Pkg.

Tech88
Regular Member
Posts: 24
Joined: Fri Nov 09, 2018 5:22 pm
Vehicle: 13' PI

Re: Rear seat sits high?

Post by Tech88 » Fri May 31, 2019 6:22 am

So I just need to carve out the foam to accommodate the crash bar? Seems easy enough

VCFP153
Regular Member
Posts: 28
Joined: Tue Mar 12, 2019 8:03 pm
Vehicle: 2017 PIS

Re: Rear seat sits high?

Post by VCFP153 » Sat Jun 01, 2019 4:50 pm

Tech88 wrote:
Thu May 30, 2019 10:54 pm
I'll have to check tomorrow. I know my PI has an administrative package with factory center console and carpet. So I assume it's a factory seat correct to the car
Mine has that package, too, but the seat seems to sit normal.

Tech88
Regular Member
Posts: 24
Joined: Fri Nov 09, 2018 5:22 pm
Vehicle: 13' PI

Re: Rear seat sits high?

Post by Tech88 » Sat Jun 01, 2019 5:04 pm

I found this seat on Ebay. I wonder if I have those channels cut out. Could the rear support be removed to remedy the seat height?
Attachments
Screenshot_20190601-170206_eBay.jpg
Screenshot_20190601-170206_eBay.jpg (913.05 KiB) Viewed 347 times

Jake_Blues
Regular Member
Posts: 69
Joined: Sun Jan 27, 2019 8:25 pm
Vehicle: 2013 Police Interceptor Sedan

Re: Rear seat sits high?

Post by Jake_Blues » Mon Jun 03, 2019 6:36 pm

Tech88 wrote:
Sat Jun 01, 2019 5:04 pm
I found this seat on Ebay. I wonder if I have those channels cut out. Could the rear support be removed to remedy the seat height?
so - have you checked the bottom of your seat or not? it's not clear whether you have or not.

yes, you can remove the cross bracing - but that reduces your rear end collision impact from 75mph to 55mph which makes it just a "civilian" car in terms of rear crash worthiness.

some folks here have done it and you can search the threads for it under rear seat.

as far as carving out the channels - easiest thing to do is trace an existing seat and transfer that tracing to the bottom of your seat if it isn't cut out.

you can use an exacto knife or get fancy and use a foam cutting knife.

https://www.amazon.com/Knife-Cutter-Sty ... B078P81GGD
https://www.harborfreight.com/130-watt- ... 60313.html

Tech88
Regular Member
Posts: 24
Joined: Fri Nov 09, 2018 5:22 pm
Vehicle: 13' PI

Re: Rear seat sits high?

Post by Tech88 » Mon Jun 03, 2019 6:47 pm

I have not checked yet. Been preoccupied lately. It is a cloth seat. I'll check tomorrow night. Is it common for the foam not to be trimmed for the reinforcement?

Jake_Blues
Regular Member
Posts: 69
Joined: Sun Jan 27, 2019 8:25 pm
Vehicle: 2013 Police Interceptor Sedan

Re: Rear seat sits high?

Post by Jake_Blues » Tue Jun 04, 2019 7:02 am

if it's an original PI seat, it will be trimmed. if it isn't - odds are no.

billross is on point tho - before the cars go to auction they get de-po-po'd, as in all the emergency equipment gets stripped. taking the back seat out or removing the fiberglass one and putting the original back in happens. if it had an original cloth or vinyl seat it gets removed to make sure no contraband or weapons are left behind.

Tech88
Regular Member
Posts: 24
Joined: Fri Nov 09, 2018 5:22 pm
Vehicle: 13' PI

Re: Rear seat sits high?

Post by Tech88 » Sat Jun 08, 2019 9:21 pm

So my seat is factory and it does have the channels cut out to accommodate the brace. I made sure it's in correctly and it still seems high. Maybe it's just me.

Post Reply